Ardex AF200 Plus Matting Bonding Adhesive (6kg)

Ardex AF200 PLUS Uncoupling Matting Adhesive is a ready mixed easy to apply matting adhesive made by leading brand Ardex. It is the new improved formula of AF200. This adhesive is ideal for installing fleece-backed uncoupling mats prior to tiling. AF200 is available in a 6kg sized tub.

Ardex AF200 PLUS adhesive is to be used in internal dry areas only. With this adhesive you can fix fleece backed matting to timber, concrete and cement or sand screed subfloors - with no need to prime! (Schluter Ditra Heat Duo should only be fixed to timber floors with Ardex AF200 PLUS). Tiling can commence immediately after the matting is laid and has a tack-life of an hour, leaving you plenty of time to work up to an hour after application. In addition Ardex AF200 PLUS has a high initial grab, limiting curling of the mat for easy installation and speeding up working time.

Using a B1 or 2mm x 6mm V-shaped notched serrated trowel, apply a ribbed bed of Ardex AF200 Plus onto the subfloor and leave it to air for 5 - 10 minutes. Place the matting fleece side down into the tacky adhesive and press firmly using a steel trowel, abutting all edges. This should give you a perfect finish.

Features and Benefits of Ardex AF200 Plus Adhesive

Ardex AF200 Plus is a ready mixed adhesive ideal for installing fleece-backed uncoupling mats prior to tiling. It has excellent grab and an exceptionally long tack time, with very good early and long term adhesive bond strength, allowing matting systems to be installed in as little as 5 minutes or up to an hour after application. Once the matting has been installed, tiling can commence immediately. Ardex AF200 Plus meets the requirement guidelines for the EMICODE licence ‘EC1 PLUS’, achieving the lowest possible emission limits.

USE

Ardex AF200 Plus is used to fix fleecebacked uncoupling matting to timber, concrete and cement/sand screed subfloors prior to tiling, and is suitable for use over normal underfloor heating systems.

SURFACE PREPARATION

Ensure adequate ventilation.

Where required, uneven subfloors can be levelled with the appropriate ARDEX Latex or Water-Based Levelling and Smoothing Compound e.g. ARDITEX NA or ARDEX K 39.

Priming is not usually required, however, on highly absorbent surfaces it can be advantageous to prime with ARDEX P 51 Priming and Bonding Agent diluted 1:3 with cold, clean water. This will maintain the open time of ARDEX AF 200 PLUS, and ensure maximum coverage of the adhesive.

Timber floor constructions should be load bearing, clean, dry and free of dust and other contaminants. Chipboard floors should be free of wax type waterproofing layers, fire retardants etc. and any other barriers to adhesion. Any repairs such as re-fixing and replacing loose/damaged boards should be carried out before applying ARDEX AF 200 PLUS.

When applying ARDEX AF 200 PLUS onto concrete or cement/sand screeds, it is essential that the subfloor is dry i.e. the moisture content is no greater than 75% RH and contains a functioning damp proof membrane. Where an effective damp proof membrane is absent, or the relative humidity of the subfloor is above 75% RH, contact ARDEX Technical Services for further information.

NOTE FOR CALCIUM SULPHATEBASED SCREEDS

Calcium sulphate screeds (anhydrite and hemihydrate screeds) should be dry, with the moisture content below 0.5% before the uncoupling matting is applied.

The screed surface is normally abraded to remove any weak and friable surface material, e.g. by belt sanding or similar, before the matting is installed. Contact the screed supplier for detailed instructions. The dry, prepared surface should be primed with ARDEX P 51 (diluted 1:3 with clean water), applied with a broom and allowed to dry. ARDEX AF 200 PLUS can then be applied but should be allowed to become tacky to improve drying prior to fixing the matting. Dependent on the information from the gypsum screed manufacturer, a suitably sand blinded coat of an epoxy primer such as ARDEX R 3 E may be required. The uncoupling matting should then be fixed with an ARDEX Cement-Based Tile Adhesive.

MIXING

ARDEX AF 200 PLUS is ready for use, but for optimum performance the adhesive should be thoroughly mixed to ensure the even dispersion of polymers before application.

APPLICATION

Dry lay the uncoupling matting prior to adhering it to the subfloor to ensure accuracy of fitting.

Apply a ribbed adhesive bed of ARDEX AF 200 PLUS to the subfloor using a B1 or 2mm x 6mm V-shaped notched serrated trowel, and leave to air for 5-10 minutes. The matting must then be laid into the wet/tacky ARDEX AF 200 PLUS fleece-side down, and pressed firmly into place using a steel trowel, abutting all edges. The matting must be installed within the 60 minute open time and can be adjusted and repositioned for up 20 minutes.

Tiling can commence immediately.

NOTE: The airing time is dependent on the absorbency of the subfloor and site conditions. Higher temperatures will shorten and lower temperatures will lengthen the time.

NOTE: If waterproofing properties are required, please refer to the matting manufacturer’s instructions for detailing of the joints between separate sections of the matting.

NOTE FOR STEEL SUBFLOORS

The steel should be rigid and abraded to provide a shiny, clean surface. ARDEX AF 200 PLUS can then be applied but should be allowed to become tacky, after approximately 10 minutes, prior to fixing the matting. Once the matting is installed, tiling can commence immediately.

TILE FIXING

Floor tiles can be fixed with an ARDEX Cement Based Tile Adhesive e.g. ARDEX MICROTEC X 77 or ARDEX MICROTEC X 78, and grouted with ARDEX-FLEX Flexible Tile Grout, or ARDEX EG 18 PLUS Epoxide Tile Grout for areas where chemical resistance and hygienic joints are required. When fixing moisture sensitive natural stone, we recommend the use of ARDEX MICROTEC S 27, ARDEX MICROTEC S 28 or ARDEX MICROTEC X 7001 Tile Adhesives and ARDEX MG Tile Grout.

NOTE: ARDITEX NA Ultra Rapid Setting Latex Levelling and Smoothing Compound can be applied direct to the uncoupling matting to create a flat, level surface ideal for tiling, making the subsequent application of the tile adhesive quicker, easier and more cost effective. For more information, consult the ARDEX Ultimate Uncoupling Matting Installation System guide or contact ARDEX Technical Services.

PACKAGING

ARDEX AF 200 PLUS is packed in plastic tubs - either 14kg or 6kg net weight.

COVERAGE

6kg of ARDEX AF 200 PLUS will fix approximately 19m² of matting, and 14kg will fix approximately 45m². For maximum coverage, use a B1 or 2mm x 6mm V-shaped notched serrated adhesive trowel and apply at a 45° angle.

NOTE: The actual coverage achieved in practice is affected by the application technique and the texture and absorbency of the subfloor.

STORAGE AND SHELF LIFE

ARDEX AF 200 PLUS has a shelf life of not less than 12 months if stored in good conditions, between 5°C and 30°C and in original unopened containers.

NOTE: For the latest technical or health and safety information on this product, consult the current technical or health and safety data sheet online at www.ardex.co.uk

NOTE: The information supplied in our literature or given by our employees is based upon extensive experience and, together with that supplied by our agents or distributors, is given in good faith in order to help you. Our Company policy is one of continuous Research and Development; we therefore reserve the right to update this information at any time without prior notice. We also guarantee the consistent high quality of our products; however, as we have no control over site conditions or the execution of the work, we accept no liability for any loss or damage which may arise as a result thereof. Country specific recommendations, depending on local standards, codes of practice, building regulations or industry guidelines, may affect specific installation recommendations.

All information supplied by Ardex UK

TECHNICAL ADVICE HELPLINE

01440 714939

ARDEX Online

www.ardex.co.uk

Click the links below to see the technical specifications and user guides for this product

• Click here to see the Ardex AF200 Adhesive Technical Data sheet
• Click here to see the Ardex AF200 Adhesive Health & Safety Data Sheet
• Click here to see the Ardex AF200 Declaration of Performance
• Click here to see the Ardex AF200 Sustainability Data Sheet
• Click here to see the Ardex AF200 Environmental Product Declaration
• Click here to see the Ardex AF200 EMICode Certificate
• Click here to see the Ardex AF200 Application Guide

Download BIM RVT Object

Download BIM LFC Object