Ardex P51 Primer Water-Based Primer & Bonding Agent

Ardex P51 Primer is a high strength concentrated water based primer and bonding agent suitable for a wide range of applications. It's primarily used for priming and preparing internal surfaces ready to receive cement-based levelling compounds, adhesives, screeds, and even plaster based materials. Ardex P51 primer helps to improve adhesion and even works to inhibit the penetration of water in intermittently damp locations.

Ardex P51 can also be used to prime porous surfaces prior to the application of Ardex water-based levelling and smoothing compounds, and wood based sheets and boards prior to the application of tile adhesive. It seals and primes whilst the blue pigment gives you clear identification whilst working. The resealable bottle is easy to use and means that you don't need to buy a new bottle for each job, and as Ardex P51 primer is solvent-free, you'll never have to deal with a nasty smell whilst working with it.

Ardex P51 Primer can also be used as a temporary protective coating over cement-based smoothing compounds and repair mortars where these have to be walked on before the flooring is applied and as a temporary dust-proofing treatment on screeds. As the primer seals pores on absorbent sub-floors, it inhibits air bubbles rising through applied sub-floor smoothing and levelling compounds, thus extending their flow life and workability.

Features & Benefits of the Ardex P51 Primer

DESCRIPTION

A concentrated, blue, synthetic, water-based, solvent- free multi-purpose primer with a wide range of applications which, after drying, helps to inhibit the penetration of water from subsequently applied materials.

USE

This product is used to prepare dry internal floors, walls and ceilings to receive cement-based mortars (levelling compounds, tile adhesives, screeds) as well as plaster based materials, improving adhesion as a bonding agent and retarding the wetting of the substrate by the applied materials.

Effective pore sealer on absorbent sub-floors inhibiting air bubbles rising through subsequently applied sub-floor smoothing and levelling compounds, thus extending their flow life and workability.

ARDEX P51 can be used to prime and seal the surfaces of cement or gypsum plaster based materials such as wall plaster, floors of cement based or prepared anhydrite and alpha hemihydrate pumped screeds before applying cement-based products such as levelling compounds and tile adhesives.

ARDEX P51 can be used as a bonding agent to improve adhesion to dense and smooth concrete sub-floors and dense cement based screeds before using repair mortars or cement-based tile adhesives. Suitable for priming rigidly supported and conditioned plywood sub-floors before fixing ceramic tiling with appropriate cement-based tile adhesives. ARDEX P51 can be used as a temporary protective coating over cement-based smoothing compounds and repair mortars where these have to be walked on before the flooring is applied and as a temporary dust-proofing treatment on screeds.

SUBSTRATE PREPARATION

Substrates must be dry, protected by a functioning DPM, firm and free from dust, water soluble materials, excess adhesive residues and other barriers to adhesion. Surface contamination such as residues of polish, wax, grease, curing agents etc. should be removed using ARDEX DGR degreaser prior to suitable mechanised preparation. ARDEX P51 is not recommended for use on metal and mastic asphalt, excess adhesive residues, ARDEX DPM, polyurethane and epoxy coatings. Consult the ARDEX P 82 Water Dispersed Epoxy Primer and ARDEX R 3 E General Purpose Epoxy Primer datasheets for guidance.

APPLICATION

Shake the container well before use and dilute when required by putting the ARDEX P51 into a clean container and mix with the required quantity of water as specified in the selected mixing ratio. Ensure that the ambient temperature and the temperature of the surface being primed are above 5°C.

If ARDEX P51 is used where moisture sensitive materials are to be subsequently applied, the substrate must be dry, i.e. with flooring materials the screed should have a RH reading not greater than 75% and, where direct to ground, protected by an effective damp proof membrane.

Apply the priming coat evenly with a soft broom or brush, over the sound, clean and dust-free surface and leave to dry thoroughly to a clear, thin blue film before beginning any subsequent work.

USE IN BONDING COATS FOR SCREEDS

ARDEX P 51 is also excellent for improving adhesion of bonded ARDEX A 35/A23 Cement and Sand Screeds. Best results are obtained by mixing ARDEX P 51 Primer 1:1 with water and then mixing this with a mix of 1 part ARDEX A 35 Cement with 1 part Screeding Sand to produce the required bonding slurry/grout consistency. May also be used to produce a bonding slurry/grout for ordinary cement and sand screeds, simply use ordinary Portland Cement in place of ARDEX A 35 Cement.

NOTE: Always apply screed fresh in fresh into Bonding Coat.

NOTE: The above coverage figures will vary depending on the roughness of the surface and absorbency of the substrate.

The following table on the use of priming coats also explains the treatment of substrates on which filling, smoothing and levelling work is to be done.

*Brush down plaster with a stiff brush to remove any weakly adhered surface residues to expose a cohesively strong matt surface.

N.B. When using ARDEX P 51 on existing substrates, ensure that the residues of levelling compounds, adhesives, etc. are water resistant, sufficiently strong to support anticipated loads and traffic and well adhered to the substrate. Allow priming coats to dry. Always completely remove adhesive residues that are water soluble or softened by water. Where adhesive residues are present on polyurethane, epoxy resin and bitumen based substrates ARDEX P 82 must be used as an adhesive bridge.

PRECAUTIONS

Aqueous synthetic polymer based dispersion. Wash off from skin before drying takes place. Any material slashed into the eye, mouth or nose should be washed away immediately with clean water. Avoid ingestion. Non-toxic and small amounts are unlikely to cause more than temporary discomfort. If large amounts are swallowed seek medical advice.

For the latest health and safety information on this product consult the current Health and Safety Data Sheet. This information is available from the website:

www.ardex.co.uk or by contacting the office in Haverhill.

STORAGE AND SHELF LIFE

ARDEX P 51 must be stored in unopened packaging, clear of the ground; in cool, dry conditions and protected from excessive draught. If stored correctly, the shelf life of this product is 12 months from the date shown on the packaging.

NOTE: The information supplied in our literature or given by our employees is based upon extensive experience and, together with that supplied by our agents or distributors, is given in good faith in order to help you. Our Company policy is one of continuous Research and Development; we therefore reserve the right to update this information at any time without prior notice. We also guarantee the consistent high quality of our products; however, as we have no control over site conditions or the execution of the work, we accept no liability for any loss or damage which may arise as a result thereof. Country specific recommendations, depending on local standards, codes of practice, building regulations or industry guidelines, may affect specific installation recommendations.

All information supplied by Ardex UK

TECHNICAL ADVICE HELPLINE

01440 714939

ARDEX Online

www.ardex.co.uk

Click the links below to see the technical specifications and user guides for this product

• Click here to see the Ardex P51 Primer Technical Data sheet
• Click here to see the Ardex P51 Primer Health & Safety Data Sheet
• Click here to see the Ardex P51 Primer Declaration of Performance
• Click here to see the Ardex P51 Primer Sustainability Data Sheet
• Click here to see the Ardex P51 Primer Environmental Product Declaration

Download BIM RVT Object

Download BIM LFC Object